SMC Networks ADSL2 Bedienungsanleitung

EZ Connect NDraft 11n Wireless USB2.0 AdapterADSL2 BARRICADE ™4-Ports Wireless Annex A ADSL/ADSL2 Modem RouterSMC7904WBRA4

3 About the Web Configuration This chapter describes how to configure the router by using the Web-based configuration utility. 3.1 How to Access th

In the navigation bar, choose Setup Wizard. In the Setup Wizard page, you can configure the VPI/VCI number. The Setup Wizard page guides fast a

The following table describes the parameters of this page. Field Description (Root) SSID SSID BroadCase Wireless Mode Channel Number After

You can choose LLC or VC-Mux. VPI The virtual path between two points in an ATM network, and its valid value is from 0 to 255. VCI The v

PPPoA If the uplink equipment supports the PPPoA encapsulation, you can set the device to initiate the PPPoA dialup. After finishing the settings,

If you ensure the configuration is correct, click FINISH. Then the configuration takes effect. You can check the configuration in the WAN page

If you ensure the configuration is correct, click FINISH. Then the configuration takes effect. You can check the configuration in the WAN page

If you ensure the configuration is correct, click FINISH. Then the configuration takes effect. You can check the configuration in the WAN page

If you ensure the configuration is correct, click FINISH. Then the configuration takes effect. You can check the configuration in the WAN page

After finishing the settings, click NEXT. The page shown in the following figure appears. If you ensure the configuration is correct, click FINIS

Contents 1 Introduction ...

I Note: After you select the country in which you are in and the correct ISP, the ADSL settings, such as protocol, connection type, VPI, and VCI

3.3.3 WLAN Choose Status > WLAN. The page that is displayed shows some basic wirless LAN settings of the router. 3.3.4 WAN Choose Status >

3.3.5 Port Mapping Choose Status > Port Mapping. In the Port Mapping page, you can view the mapping relation and the status of port mapping. 3.

3.3.6.2 DSL Statistic Choose DSL Statistic in the left pane. The page shown in the following figure appears. In this page, you can view the ADSL line

3.4.1 LAN Settings Choose LAN > LAN Settings. In the LAN Settings page, you can configure the LAN network. In this page, you can change IP addr

Select DHCP Proxy in the DHCP Server Setup page. The page shown in the following figure appears. The following table describes the parameters of th

The following table describes the parameters in this page. Field Description DHCP Server If set to DHCP Server, the router can assign IP ad

Description Field the assigned IP addresses before the IP addresses change. Refresh Refresh the page. Close Close the page. Click MAC-based Assign

3.5.1 Basic Settings Choose WLAN > Basic Settings. The page shown in the following figure appears. In this page, you can configure the parameters

The following table describes the parameters and buttons of this page. Field Description Vap SSID The service set identification (SSID) is a

xvii3.7.8 Other...

The following table describes the parameters and buttons of this page. Field Description SSID Type Select the SSID. Encryption You can choose Non

The following table describes the parameters and buttons of this page. Field Description SSID TYPE Select the SSID. Key Length Select 64-bit or

The following table describes the parameters of this page. Field Description Fragment Threshold This is the maximum data fragment size (between 25

The following table describes the parameters and buttons of this page. Field Description Select Access Control Mode You can choose Disable, Allo

The following table describes the fields of this screen. Label Description Enable WDS Select it to enable the WDS function. Otherwise, you

The following table describes the parameters of this page. Field Description Current ATM VC Table This table shows the existed PVCs. It shows the I

Field Description If select Use DHCP, the router is a DHCP client, the WAN IP address is assigned by the remote DHCP server. Local IP Address It

The following table describes the parameters and buttons of this page. Field Description 3.6.2 ADSL Settings Choose WAN > ADSL Se

3.7 Advance In the navigation bar, choose Advance. The Advance page that is displayed contains DNS, Firewall, Virtual Server, Routin

The following table describes the parameters and buttons of this page. Field Description Obtain DNS Automatically Select it, the router accept

1 Introduction The SMC7904WBRA4 supports multiple line modes. It provides four 10/100 base-T Ethernet interfaces at the user end. The device prov

3.7.2 Firewall Choose Advance > Firewall. The Firewall page that is displayed contains IP/Port Fileter, MAC Filter, and URL Blocking. 3.7.2.1 IP

Field Description 3.7.2.2 MAC Filter Choose MAC Filter in the left pane. The page shown in the following figure appears. Entries in thi

Field Description 3.7.2.3 URL Blocking Choose URL Blocking in the left pane. The page shown in the following figure appears. This page is

Click Add to add a virtual server. The page shown in the following figure appears. The following table describes the parameters and buttons of this

3.7.4 Routing Choose Advance > Routing. The page shown in the following figure appears. The page that is displayed contains Static Route and RIP

3.7.4.2 RIP Choose RIP in the left pane. The page shown in the following figure appears. If you are using this device as a RIP-en

3.7.5 IP QoS Choose Advance > IP QOS. The page shown in the following figure appears. Entries in this table are used to assign

3.7.6 Anti-dos Choose Advance > Anti-Dos. The page shown in the following figure appears. Denial-of-service attack (DoS Attack) is

3.7.8 Other Choose Advance > Other. In the Other page that is displayed contains IGMP Proxy, UPNP, Bridge, and IP PassThrough.3.

Click Apply Changes to save the settings of this page. 3.7.8.2 UPNP Choose UPNP in the left pane. The page shown in the following figure appe

Front panel The following table describes the LEDs of the device. LED Status Color Description On The device is powered on and the initialization

The following table describes the parameters and buttons of this page. Field Description Click Show MACs. The page shown in the

3.8 Admin In the navigation bar, choose Admin. The Admin page that is displayed contains Remote Access, Commit/Reboot, Password, Backup/Restore, Up

The following table describes the parameters of this page. Field Description reset to default settings Select it to reset the router to the defaul

Field Description user. New Password Enter the password to which you want to change the old password. Confirmed Password Enter the new password ag

The following table describes the parameters and buttons of this page. Field Description Select File Click Browse to select the firmware file. Uplo

Refresh Refresh the system shown in the page. Time Mode You can choose Time Server or Manual. Select Time Server, the router gets the system time

The following table describes the parameters and buttons of this page. Field Description Trap IP Address Enter the IP address of trap IP. The trap

The following table describes the parameters and buttons of this page. Field Description 3.8.10 ACL Choose Admin > ACL. The pag

Step 1 Select Enable and click take effect. Step 2 Configure the ACL. Step 3 Click take effect to take the configuration effect. I Note: If you s

Field Description Host Address Enter the IP address. Go ! Click it to begin to Ping the host address. 3.9.2 ATM Loopback Choose Diagnostic >

Interface Function The button of the antenna. 1.4 System Requirements Recommended system requirements are as follows: A 10/100 base-T Ethernet

573.9.4 Diagnostic Choose Diagnostic. The page shown in the following figure appears. In this page, you can test the DSL connection. Click Run Dia

Appendix A Questions & Answers This section describes common problems you may encounter and possible solutions to them. The Barricade can be easi

Click start -> run (input ping demands)-> Ping 192.168.2.1 (MODEM IP address). If cannot reach the modem, please check following configuratio

Appendix B Technical Specifications External Connectors 1 push power switch 1 DC power jack 1 factory reset button 4 LAN 10/100M Auto MDI/MDI

Ethernet Feature Fully compliant with IEEE802.3/802.3u auto-negotiation function Support 10base-T, 100base-TX Support half duplex, full duplex

Appendix C GPL Anouncement GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Str

The precise terms and conditions for copying, distribution and modification follow. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING,

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasona

this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be s

4 PPP session PAP and CHAP IP filter IP QoS Remote access control Line connection status test Remote management (telnet and HTTP) backu

REPAIR OR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO M

68 The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the command

SMC7904WBRA4

2 Hardware Installation Step 1 Connect the Line interface of the device and the Modem interface of the splitter through a telephone cable. Connect t

6 Figure 2 (with a telephone set before the splitter) In the actual application, connection 1 is recommended. I Note: When connection 2 is used