Smc-networks EtherNet/IP EX500-GEN1 Bedienungsanleitung

Reduced wiring systemEX500-GEN1Instruction ManualEtherNet/IP™ Compatible GW UnitSpecifications are subject to change without prior notice and any obli

16 17Wiring (continued )For GW unit – Manifold valve – Input unit manifold configurationTwo communication connectors in SI unit and one communication

GATEWAY UNITEX500 SERIESCOM A COM B COM C COM DLANNSMS100LINKPWR18 19Display/Switch SettingDisplayNOTEWhen connecting manifold valve only without conn

2120SI Unit Part NamesThe SI unit is the unit to communicate with GW unit in combination with manifold valve.It can be used with SV series valves an

2322Mounting/WiringThe mounting and removing methods of SI unit are as shown below.For branch wiring method, refer to subsection "Wiring" (

2524DisplayPower LEDCommunication LEDSI unit for SV series valves ( EX500-S 01 )Power LEDCommunication LEDSI unit for VQC series valves ( EX500-Q )Pow

2726Dimensions ( unit : mm )When only input blocks for M8 connector are connected44.239.7L3(L4)5L1L2 ( Rail mounting pitch: 12.5 )DIN Rail354932.2(7.5

2928SpecificationSpecifications for Input unitConnected blockCurrent source type input block ( PNP input block )orCurrent sink type input block ( NPN

3130Correspondence between input number and input blockInput block up to 8 can be connected ( 16 points ).Input numbers are 0 to 15 from Input unit si

33322. EX9-PE1VQC seriesSI unit forgeneral purposeoutput block( EX500-Q 02 )Dimensions ( unit : mm )21.259.872.62126.722.243.21. EX9-OET1/EX9-OET2/

3534WiringOutput wiringConnect output devices to the output connectors.EX9-OET1/EX9-OET2/EX9-OEP1/EX9-OEP2 output connectorsM12, 5-pin, socketNOTEMou

Thank you for purchasing the SMC reduced wiring system EX500 series.Please read this instruction manual carefully and understand the contents beforeus

3736M12, 5-pin, reverse key, socketPower supply wiringWhen combining EX9-OEP1 ( or EX9-OEP2 ) and EX9-PE1 and using external powersupply, connect the

3938Display1. EX9-OET1/EX9-OET2/EX9-OEP1/EX9-OEP20Lights on : Output ( OUT 0 ) is ON.Lights off : Output ( OUT 0 ) is OFF.1Lights on : Output ( OUT 1

4140NOTETighten the waterproof cap by the specified tightening torque.( 0.05N m for M8, 0.1N m for M12 )Waterproof capMounted on unused ports of GW un

4342MS LED statusNormal status : Lit in greenFatal failure : Lit in red1The effect of noise is possible. Checkthe installation conditions. If the trou

2 3SAFETYThe body of unit and this manual contain the essential information for the protection ofusers and others from possible injury and property da

4 5SAFETY ( continued )Follow the instructions given below when handling your reduced wiring system.Otherwise a damage or failure to cause a malfuncti

6 7EX500 Part NamesCommunicationconnector12345678Note1 : For wiring method, refer to subsection "Wiring" ( page 11 ) of section "EX500

8 9SpecificationBasic specificationsRated voltage 24VDCRange of powersupply voltage Power supply for input and controlling GW/SI : 24VDC 10%Power supp

10 11WiringSpecification ( continued )The wirings is explained in the following order.Communication wiring : Connection with EtherNet/IPPower supply w

12 13Wiring ( continued )Communication wiringAligning the key groove with the communication connector( 4-pin, socket ) of GW unit, plug the Ethernetco

24VDC24VDCBrown : 0V ( for solenoid valves/output )White : 24VDC ( for solenoid valves/output )Gray : Ground ( PE )Blue : 0V ( for input and con