Smc-networks Barricade SMC7004ABR Bedienungsanleitung

Barricade™Broadband Router10/100 Mbps Broadband Router◆ Internet access via –• 10/100 Mbps WAN port connection to xDSL/Cable modem, or• RS-232 consol

COMPLIANCESx11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannun

CABLESB-2Figure B-1 illustrates how the pins on the RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attachin

CABLESB-3RJ-45 Port Pin AssignmentsAll LAN ports on the Barricade support automatic MDI/MDI-X configuration. This means that the pin signals in use wi

CABLESB-4Serial Port Pin AssignmentsThe DB-9 serial port on the rear panel is used to connect the Barricade to an ISDN TA or PSTN modem. The pin assig

CABLESB-5Serial Port to 9-Pin COM Port on PCSerial Port to 25-Pin DCE Port on ModemSerial Port to 25-Pin DTE Port on PCBarricade’s 9-Pin Serial PortCC

CABLESB-6Printer Port Pin AssignmentsThe DB-25 parallel port on the Barricade’s rear panel is used to connect the Barricade to a printer. When a print

C-1APPENDIX CSPECIFICATIONSWAN Interface10BASE-T/100BASE-TX, 1 RJ-45 portSerial, 1 RS-232 DB-9 connectorPrinter InterfaceParallel1 DB-25 printer portM

SPECIFICATIONSC-2Humidity5% to 95% (noncondensing)CompliancesCE MarkEmissionsFCC Class BVCCI Class BIndustry Canada Class BEN55022 (CISPR 22) Class BC

SPECIFICATIONSC-3SMC7004ABRLAN Interface10BASE-T/100BASE-TX4 RJ-45 portsIndicator PanelLAN (Link, Activity), WAN (Link, Activity), PowerDimensions19.5

SPECIFICATIONSC-4SMC7008ABRLAN Interface8 RJ-45 portsPorts 1-7:Twisted-pair, fixed crossoverPort 8: Twisted-pair, alternate MDI/MDI-X, choice between

D-1APPENDIX DORDERING INFORMATIONBarricade Broadband Router ProductsSMC7004ABR 4-port Residential Gateway - WAN/LAN/Print ServerSMC7008ABR 8-port Resi

TABLE OF CONTENTSxiTABLE OF CONTENTS1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1About the Barricade . . . . . . . . .

ORDERING INFORMATIOND-2

6 HughesIrvine, CA 92618Phone: (949) 707-2400FOR TECHNICAL SUPPORT, CALL:From U.S.A. and Canada (24 hours, 7 days a week)(800) SMC-4-YOU; (949) 707-24

TABLE OF CONTENTSxiiStatic IP Address – Fixed IP . . . . . . . . . . . . . . . . . 4-10PPP over Ethernet – PPPoE . . . . . . . . . . . . . . . . .

TABLE OF CONTENTSxiii6 Configuring Printer Services . . . . . . . . . . . . . . . 6-1Install the Printer Port Monitor . . . . . . . . . . . . . . .

TABLE OF CONTENTSxiv

1-1CHAPTER 1INTRODUCTIONCongratulations on your purchase of the Barricade™ Broadband Router. SMC is proud to provide you with a powerful yet simple co

FEATURES AND BENEFITS1-2Features and Benefits• Internet connection to xDSL or Cable modem via a 10/100 Mbps WAN port• Internet connection to ISDN TA o

INTRODUCTION1-3ApplicationsMany advanced applications are provided by the Barricade, such as:• LAN AccessThe Barricade provides connectivity to 10/100

APPLICATIONS1-4• User-Definable Application Sensing TunnelYou can define special applications that require multiple connections such as Internet gamin

INTRODUCTION1-5• Point-to-Point Tunneling Protocol – Provides a secure tunnel for remote client access to a PPTP security gateway. PPTP includes provi

APPLICATIONS1-6

2-1CHAPTER 2INSTALLATIONBefore installing the Barricade™ Broadband Router, verify that you have all the items listed under “Package Contents.” If any

INSTALLATION2-2Please fill out and return the Warranty Registration Card to SMC or register on SMC’s Web site at www.smc.com. The Barricade Broadband

INSTALLATION2-3• 4/8 RJ-45 ports for connection to a 10BASE-T/100BASE-TX Ethernet Local Area Network (LAN). These ports can auto- negotiate the operat

INSTALLATION2-4SMC7008ABRFigure 2-1. Front and Rear PanelsItem DescriptionReset ButtonUse this button to reset the power and restore the default fact

INSTALLATION2-5System RequirementsYou must have an ISP that meets the following minimum requirements:• Internet access from your local telephone compa

INSTALLATION2-6You should also remember to turn off the power, remove the power cord from the outlet, and keep your hands dry when you install the Bar

INSTALLATION2-7Attach to Your Network Using Ethernet CablingThe 4/8 LAN ports on the Barricade can auto-negotiate the connection speed to 10 Mbps Ethe

INSTALLATION2-82. Make sure each twisted-pair cable does not exceed 100 meters (328 feet).Figure 2-3. Making LAN ConnectionsAttach the Barricade to t

INSTALLATION2-9Note: When connecting to the WAN port, use 100-ohm Category 3, 4 or 5 shielded or unshielded twisted-pair cable with RJ-45 connectors a

6 HughesIrvine, CA 92618Phone: (949) 707-2400Barricade™Broadband RouterUser GuideFrom SMC’s Barricade line of Broadband RoutersSeptember 2001Revision

INSTALLATION2-10Verify Port Status Check the power and port indicators as shown in the following table.LED Condition StatusPower(Green)On Barricade i

3-1CHAPTER 3CONFIGURING CLIENT PCSTCP/IP ConfigurationTo access the Internet through the Barricade™ Broadband Router, you must configure the network s

PRINTER CLIENT INSTALLATION3-2Printer Client Installation If you need to provide print services for devices attached to the Barricade, then install th

4-1CHAPTER 4CONFIGURING THE BARRICADEAfter you have configured TCP/IP on a client computer, you can use a Web browser to configure the Barricade™ Broa

NAVIGATING THE WEB BROWSER INTERFACE4-2Navigating the Web Browser InterfaceThe Barricade’s management interface includes four key menus – Status, Help

CONFIGURING THE BARRICADE4-3Making Configuration ChangesConfigurable parameters have a dialog box or a drop-down list. Once a configuration change has

MAIN MENU4-4Main MenuUsing the Web management interface, you can define system parameters, manage and control the Barricade and its ports, or monitor

CONFIGURING THE BARRICADE4-5DHCP Client Log Displays information on all DHCP clients attached to your network.Tools Menu Contains options to reset th

NETWORKING AND CLIENT SERVICES4-6Networking and Client ServicesUse the Setup menu to configure the LAN interface (including TCP/IP parameters for the

CONFIGURING THE BARRICADE4-7Change PasswordUse this menu to restrict management access based on a specific password. Anyone can access the Status and

CopyrightInformation furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for i

NETWORKING AND CLIENT SERVICES4-8Set Time ZoneSet the time zone for the Barricade. This information is used for log entries and client filtering.LAN G

CONFIGURING THE BARRICADE4-9the Barricade in the client address pool. WAN ConfigurationSpecify the WAN connection type required by your Internet Servi

NETWORKING AND CLIENT SERVICES4-10Dynamic IP Address – DHCPThe Host Name is optional, but may be required by some ISPs. The default MAC address is set

CONFIGURING THE BARRICADE4-11Note: You may need a fixed address if you want to provide Internet services, such as a Web server or FTP server.PPP over

NETWORKING AND CLIENT SERVICES4-12Dial-up on Demand – ModemIf you are accessing the Internet via an ISDN TA or PSTN modem attached to the serial port

CONFIGURING THE BARRICADE4-13Modem Initialization string – Enter the initialization string provided by your modem manufacturer. The following is a sam

NETWORKING AND CLIENT SERVICES4-14Configuring Client ServicesThe Barricade includes a broad range of client services, including firewall protection, n

CONFIGURING THE BARRICADE4-15Virtual ServerIf you configure the Barricade as a virtual server, remote users accessing services such as Web or FTP at y

NETWORKING AND CLIENT SERVICES4-16HTTP request from outside users will be transferred to 192.168.2.2. Therefore, by just entering the IP Address provi

CONFIGURING THE BARRICADE4-17Specify the port normally associated with an application in the “Trigger Port” field, select the protocol type as TCP or

vLIMITED WARRANTYLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, un

NETWORKING AND CLIENT SERVICES4-18MiscAdministrator Time-out – Enter time-out setting in minute for administration protection.Discard PING from WAN si

CONFIGURING THE BARRICADE4-19Viewing Network and Device StatusYou can use the following screen to display WAN/LAN connection status, firmware and hard

USING SYSTEM TOOLS4-20Using System ToolsYou can use the “Tools” menu to reboot the Barricade, restore factory settings, or update firmware.The “Backup

5-1CHAPTER 5CONFIGURING CLIENT TCP/IPIf you have not previously installed the TCP/IP protocol on your client PCs, refer to the following section. If y

INSTALLING TCP/IP PROTOCOL IN YOUR PC5-25. Select the Microsoft item in the manufacturers list. And choose TCP/IP in the Network Protocols. Click the

CONFIGURING CLIENT TCP/IP5-3Setting TCP/IP to Work with the Barricade1. Click the Start button and choose Settings, then click Control Panel.2. Double

SETTING TCP/IP TO WORK WITH THE BARRICADE5-4Configuring Your Computer with Windows 95/98/MEYou may find that the instructions here do not exactly matc

CONFIGURING CLIENT TCP/IP5-52. From "Control Panel," double-click the "Network" icon.3. In the "Network" window, under t

SETTING TCP/IP TO WORK WITH THE BARRICADE5-64. Select the "IP Address" tab.If "Obtain an IP address automatically" is already sele

CONFIGURING CLIENT TCP/IP5-77. Click the "DNS Configuration" tab. Locate the DNS servers listed under "DNS Server Search Order." R

LIMITED WARRANTYviWARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY SHALL BE REPAIR OR REPLACEM

SETTING TCP/IP TO WORK WITH THE BARRICADE5-8Internet Explorer1. Open Internet Explorer and click the stop button. Click "Tools," then "

CONFIGURING CLIENT TCP/IP5-9Netscape1. Open Netscape and click the stop button. Click "Edit," then click "Preferences..."2. In the

SETTING TCP/IP TO WORK WITH THE BARRICADE5-101. Click "Start," then "Run..."2. Type "WINIPCFG" and click "OK."

CONFIGURING CLIENT TCP/IP5-11Configuring Your Computer with Windows 2000Step 1. Configure TCP/IP SettingsAfter you have completed the hardware setup,

SETTING TCP/IP TO WORK WITH THE BARRICADE5-122. Double-click the "Network & Dial-Up Connections" icon.3. Double-click the icon that corr

CONFIGURING CLIENT TCP/IP5-135. Double-click "Internet Protocol (TCP/IP)."6. All the information that you need to record is on the "Int

SETTING TCP/IP TO WORK WITH THE BARRICADE5-14Step 2. Disable HTTP ProxyYou will need to verify that the "HTTP Proxy" feature of your Web bro

CONFIGURING CLIENT TCP/IP5-152. In the "Internet Options" window click the "Connections" tab. Next, click the "LAN Settings..

SETTING TCP/IP TO WORK WITH THE BARRICADE5-162. In the "Preferences" window, under "Category" double-click "Advanced," t

CONFIGURING CLIENT TCP/IP5-172. In the "Command Prompt" window, type "IPCONFIG /RELEASE" and press the <ENTER> key.3. Type &

viiCOMPLIANCESFCC - Class BThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

SETTING TCP/IP TO WORK WITH THE BARRICADE5-18Configuring Your Computer with Windows NT 4.0Step 1. Configure TCP/IP SettingsAfter you have completed th

CONFIGURING CLIENT TCP/IP5-193. Select the "Protocols" tab.4. Double-click "TCP/IP Protocol."5. Select the "IP Address"

SETTING TCP/IP TO WORK WITH THE BARRICADE5-207. In the "TCP/IP Properties" dialog box, click the IP address tab to locate your IP address, s

CONFIGURING CLIENT TCP/IP5-21Step 2. Disable HTTP ProxyYou will need to verify that the "HTTP Proxy" feature of your Web browser is disabled

SETTING TCP/IP TO WORK WITH THE BARRICADE5-223. Clear all the checkboxes.4. Click "OK," and then click "OK" again to close the &qu

CONFIGURING CLIENT TCP/IP5-23old IP settings and renewing them with settings from your Barricade, you will also verify that you have configured your c

SETTING TCP/IP TO WORK WITH THE BARRICADE5-24These values confirm that your Barricade is functioning.4. Type "EXIT" and press <ENTER>

CONFIGURING CLIENT TCP/IP5-251. Pull down the Apple Menu. Click "Control Panels" and select TCP/IP.2. In the TCP/IP dialog box, make sure th

SETTING TCP/IP TO WORK WITH THE BARRICADE5-26already configured for DHCP. Close the TCP/IP dialog box, and skip to Step 2 "Disable HTTP Proxy.&qu

CONFIGURING CLIENT TCP/IP5-27Internet Explorer1. Open Internet Explorer and click the stop button. Click "Edit" and select "Preferences

COMPLIANCESviiiIndustry Canada - Class BThis digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as

SETTING TCP/IP TO WORK WITH THE BARRICADE5-282. In the "Preferences" dialog box, In the left-hand column labeled "Category," selec

CONFIGURING CLIENT TCP/IP5-291. Pull down the Apple Menu. Click "Control Panels" and select TCP/IP.2. In the TCP/IP window, your new setting

SETTING TCP/IP TO WORK WITH THE BARRICADE5-303. Close the TCP/IP window.Dynamic IP Allocation via a DHCP ServerSelect Obtain an IP address automatical

CONFIGURING CLIENT TCP/IP5-31Manual IP Configuration1. Select Specify an IP address in the IP Address tab. Select an IP address based on the default n

SETTING TCP/IP TO WORK WITH THE BARRICADE5-324. After finishing TCP/IP setup, click OK, and then reboot the computer. After that, set up other PCs on

CONFIGURING CLIENT TCP/IP5-33If you can successfully Ping the Barricade, then you are now ready to connect to the Internet!

SETTING TCP/IP TO WORK WITH THE BARRICADE5-34

6-1CHAPTER 6CONFIGURING PRINTER SERVICESIf you want to use the print server built into the Barricade, then you must first install the Port Monitor pro

INSTALL THE PRINTER PORT MONITOR6-22. The next screen indicates that the print client uses TCP/IP network protocol to monitor print requests. Click Ne

CONFIGURING PRINTER SERVICES6-34. Select the Program Folder that will contain the program icon for uninstalling the port monitor, and then click Next.

COMPLIANCESixSafety ComplianceUnderwriters Laboratories Compliance StatementImportant! Before making connections, make sure you have the correct cord

CONFIGURE THE PRINT SERVER6-4Configure the Print ServerThe Barricade’s print server supports Microsoft Windows 95/98/ME/NT/2000, and Unix. If you are

CONFIGURING PRINTER SERVICES6-53. Specify the printer type attached to the Barricade.4. Select the monitored port. The default port name is “SMC100” a

CONFIGURE THE PRINT SERVER6-6Configure the Network Printer in Windows NT1. On a Windows NT platform, open the Printers window in the My Computer menu,

CONFIGURING PRINTER SERVICES6-73. Select the monitored port. The default port name is “SMC100.” Then click the Configure Port button. 4. Enter the IP

CONFIGURE THE PRINT SERVER6-8Configure the Network Printer in Unix SystemsFollow the traditional configuration procedure on Unix platforms to set up t

A-1APPENDIX ATROUBLESHOOTINGThis appendix describes common problems you may encounter and possible solutions. The Barricade can be easily monitored th

TROUBLESHOOTINGA-2LED IndicatorsLink LED is Off • Verify that the Barricade and attached device are powered on. • Be sure the cable is plugged into bo

TROUBLESHOOTINGA-3Management ProblemsCannot connect using the Web browser• Be sure to have configured the Barricade with a valid IP address, subnet ma

TROUBLESHOOTINGA-4

B-1APPENDIX BCABLESEthernet CableSpecificationsTwisted-pair CableCaution: DO-NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pai